EcoPower 180
- EcoPower Series range of Injection Moulding Machines
The promise: energy-saving, clean and compact
The all-electric EcoPower, with clamping forces ranging from 55 to 300 t, combines efficiency with precision. The beltless EcoPower scores with a compact
injection unit and the clean design of its clamping unit, together with a highly efficient direct drive. The machine also offers a small footprint and
is open at the top and on the injection side.
Fast, precise injection
The injection unit is laid out for high-speed and high-precision
injection processes even under maximum injection pressure.
The encapsulated drive is clean and compact. Injection and
metering are effected via a dual drive with a circulating ball
spindle at its center.
The EcoPower comes with air cooling as standard and two
extension options: water cooling with either an open or a
closed cooling circuit.
Barrel change from above
Peripheral equipment from Wittmann built into the machine frame
helps to substantially reduce the machine`s space requirements. The
entire peripheral equipment can also be operated, visualized and its
data stored directly via the machine`s Unilog B6 control system.
Optional Features
Hydraulic
- Hydraulic core pulls incl. add. drive system. Limit switch function according
- EUROMAP 13. Pressure and speeds adjustable (only for standard base machine).
- Pneumatic core pull
- Core pull pressure release
- Pneumatic manifold for Mouldmaster nozzle (controlled 1 nozzle or more
- parallel in the mould)
Clamping Unit
- Non-standard mould hight after customers request
- T-slots in mould platens
- SPI bolt pattern
- Servo electric ejector (only for standard base machine)
- Ejector cross in clamping platen as per EUROMAP/SPI
- Mechanical ejector couple
- Ejector platen safety device as per EUROMAP 13
- Mechanical mould safety mechanism
- Parts chute
- Parts chute for separation of good/bad parts
- Photoelectric ejection check
- Air valve, action initiated (ON) and timer (OFF)
- Quick mold clamping system magnet.
Injection Unit
- Grooves in the feeding zone of barrel for improved feeding
- Increased injection- and plasticizing performance
- High temperature heaterbands up to 450 °C
- Barrel insulation
- Ball type screw tip
- Needle type shutoff nozzle with spring, pneumatic operated
- Melt temperature- or pressure sensor in cylinder head
- Wear resistant screw and barrel AK+
- Screw with mixing section or barrier section
- Liquid Silicon unit
- Vacuum pump
- Hoppermagnet
- Hopper loader UNIFEED A1
Safety gate
- Safety gate on the rear side
- Electric safety gate at the operator side
- Front side safety system for manual part removal
- Initiate next cycle by closing safety gate in semi-auto operation
- Safety gate clearance operator side/rear side extended
- Safety gate rear side lowered at the top of the upper tiebar
Cooling and Conditioning
- Watercooling with open cooling system incl. prefilter
- Watercooling with closed cooling system
- Additional flow controller with temperature gauges
- Shut-off valve for cooling water battery
- Blow out valve for cooling water battery
- Hosting of cooling circuits on the fixed platen of the moving platen
- Integrated Wittmann Temperating units and Dryer
Electrical components
- Pressure transducer for meltpressure switch over
- Temperature control zone for hot runner
- Special voltage
- Control cabinet cooler
- Manual board
- Closed loop temperature control of mould
- Additional socket
- Fuse protection for sockets
- Interface for handling equipment
- Energy consumption analysis
- Switch over to holding pressure by cavity or melt pressure
- Switch over to holding pressure by external signal
- Injection compression and venting sequences
- Purging program through the open mold
- Melt cushion control
- Audible alarm
- Analaog temperature control interface
- Temperature control interface digital, serial 20mA TTY protocol
- CAN-Bus-interface for mold conditioner as per EUROMAP 66-2
- Interface for Wittmann dryer integrated
- Interface for Wittmann Temperating units integrated
- Interface for Airmould ® mobile
- Interface for robots as per EUROMAP 67
- Adaptor from EUROMAP 67 to EUROMAP 12
- Interface for conveyor belt
- Interface for fully integration of robot incl. Ethernet switch
- Host computer interface/PDA (EUROMAP 63)
- Relays contact parallel to plasticizing
- Machine fault (potential-free contact)
- BNC connectors for injection process analysis
- Interface for vacuum pump
- Second injection data setting for automatic start up
- Web- and remote service
Additional Equipment
- Special paint and/or Touch-up paint
- Tool kit
- Levelling pads
- USB stick for data storage
- Lighting in mold space
Download EcoPower 180 PDF Brochure
